{"id":5693,"date":"2026-10-09T03:41:52","date_gmt":"2026-10-09T03:41:52","guid":{"rendered":"https:\/\/ghsprosa.co.za\/index.php\/2026\/10\/09\/cut-resistant-glove-ratings-explained\/"},"modified":"2026-10-09T03:41:52","modified_gmt":"2026-10-09T03:41:52","slug":"cut-resistant-glove-ratings-explained","status":"publish","type":"post","link":"https:\/\/ghsprosa.co.za\/index.php\/2026\/10\/09\/cut-resistant-glove-ratings-explained\/","title":{"rendered":"Cut Resistant Glove Ratings Explained Simply"},"content":{"rendered":"<p>A glove marked as cut resistant may be suitable for handling sheet metal, but entirely wrong for fitting small components or working near a rotating blade. Cut resistant glove ratings explained properly means looking beyond a single number. The rating shows laboratory performance against a defined test, while the right glove must also suit the material handled, the force used, required dexterity and other hazards present on site.<\/p>\n<p>For procurement and safety teams, this distinction matters. Selecting an unnecessarily heavy glove can reduce grip and compliance; selecting too little protection can expose workers to serious hand injuries and avoidable downtime.<\/p>\n<h2>Cut resistant glove ratings explained: what the label tells you<\/h2>\n<p>Most industrial cut-resistant gloves carry either an EN 388 rating, an ANSI\/ISEA 105 cut rating, or both. These standards use different test methods and scales. They are useful decision tools, but their figures cannot be treated as direct equivalents.<\/p>\n<p>A rating is not a guarantee that a glove cannot be cut. No glove is cut-proof. Performance depends on the sharpness and type of edge, contact pressure, angle of the blade, movement of the hand, glove condition and how the wearer uses the glove. A glove that resists a controlled straight-blade test may still be vulnerable to a puncture, a serrated edge, a power tool or a high-force slicing action.<\/p>\n<p>The product marking should therefore be read alongside the manufacturer\u2019s technical information and the findings of the workplace risk assessment.<\/p>\n<h2>Understanding EN 388 glove markings<\/h2>\n<p>EN 388 is widely used for gloves intended to protect against mechanical risks. The familiar shield-shaped pictogram is followed by a series of numbers and, in many cases, letters. Each position refers to a separate test rather than an overall protection score.<\/p>\n<h3>Abrasion, blade cut, tear and puncture<\/h3>\n<p>The first four characters normally indicate resistance to abrasion, blade cut, tearing and puncture.<\/p>\n<p>Abrasion resistance is graded from 1 to 4. A higher result generally indicates better resistance where gloves rub against rough surfaces or are used repeatedly for handling abrasive materials.<\/p>\n<p>The second figure is the original blade cut test, often called the coupe test, graded from 1 to 5. It measures the number of cycles required for a rotating blade under a fixed load to cut through the sample. This test remains useful for some materials, but it can be less reliable with high-performance fibres that blunt the test blade.<\/p>\n<p>Tear resistance, graded from 1 to 4, indicates the force needed to tear the glove material. Puncture resistance, also graded from 1 to 4, measures resistance to a pointed probe. A high cut rating does not automatically mean high puncture protection. This is particularly relevant when handling sharp offcuts, wire, splintered timber or components with pointed edges.<\/p>\n<h3>The ISO 13997 cut test: A to F<\/h3>\n<p>Where a glove material causes the coupe-test blade to dull, EN 388 uses the ISO 13997 test. This is the letter commonly seen after the four numerical results, ranging from A to F.<\/p>\n<p>The test uses a straight blade and increasing force to establish the load needed to cut through the material. Level A is the lowest cut-resistance band and Level F is the highest. Because it measures force rather than rotating-blade cycles, it is generally the more useful EN 388 cut indicator when selecting gloves for significant sharp-edge hazards.<\/p>\n<p>A glove rated EN 388 4X43D, for example, has abrasion level 4, no valid coupe result shown as X, tear level 4, puncture level 3 and ISO 13997 cut level D. The X does not mean the glove failed. It often means the coupe test was not applicable or was stopped because blade dulling affected the result.<\/p>\n<h3>Impact protection and optional markings<\/h3>\n<p>An additional P can appear after the cut letter. It confirms that the glove passed the EN 13594 impact test for knuckle protection. This may be relevant for maintenance, construction, mining and materials-handling work where knocks and crush-type contact are credible risks.<\/p>\n<p>Other markings may identify protection from heat, cold, chemicals, welding hazards or electrostatic properties. These should never be assumed from a cut rating alone. A glove designed for sharp metal may not be appropriate for hot parts, oils, solvents or electrical work.<\/p>\n<h2>How ANSI cut levels differ<\/h2>\n<p>ANSI\/ISEA 105 is another widely recognised glove standard, especially on products sourced from global manufacturers. Its cut scale runs from A1 to A9 and is based on the grams of force needed for a blade to cut through the material in a standardised test.<\/p>\n<p>Broadly, A1 offers light cut protection and A9 is intended for the highest cut hazards. The middle bands are often encountered in day-to-day industrial applications: A3 to A4 can suit general handling of sharp-edged materials, while A5 and above may be needed for demanding metal, glass or waste-handling tasks. The correct level still depends on the specific exposure.<\/p>\n<p>Do not assume that EN 388 Level C is the same as ANSI A3, or that an EN 388 Level F automatically aligns with ANSI A9. Although both systems assess cut resistance, their test apparatus, reporting bands and product claims differ. When standardising glove specifications across sites or suppliers, state the required standard and rating rather than using vague instructions such as high cut resistance.<\/p>\n<h2>Match the rating to the task, not the job title<\/h2>\n<p>The best starting point is to identify the actual cut hazard. A warehouse operative opening cartons with a safety knife faces a different risk from a fabricator handling sharp sheet metal, even if both roles are described as general handling.<\/p>\n<p>Consider the edge being handled, how sharp it is, whether the worker grips or slides it, the likely contact area and the force that may be applied. Also consider frequency. A low-risk action repeated hundreds of times per shift can create meaningful exposure, particularly when gloves become worn or contaminated.<\/p>\n<p>For light assembly and packaging, a lower cut level with a thin liner may provide adequate protection while preserving touch sensitivity. For automotive parts, glass, metal fabrication or recycling, a higher ISO 13997 or ANSI rating may be justified. In applications involving very sharp, heavy or awkward materials, the glove may need high cut protection as well as reinforced palm coverage, strong grip and impact protection.<\/p>\n<p>There is a trade-off. Higher protection can mean a thicker construction, less fingertip control and greater hand fatigue. Modern engineered yarns have improved this balance, but workers should still trial gloves during real tasks. A glove that stays in a locker because it is uncomfortable does not control the risk.<\/p>\n<h2>Other performance features that affect safety<\/h2>\n<p>Cut resistance is only one part of glove selection. Grip is critical where workers handle oily metal, wet glass or smooth components. A nitrile, polyurethane or textured palm coating can improve control, but the coating must suit the environment and should not create incompatibility with oils or chemicals in use.<\/p>\n<p>Fit also affects performance. Gloves should be available in suitable sizes, with a close and comfortable fit that allows the worker to grip naturally. Loose fingertips can snag and make fine work more difficult; an overly tight glove can cause fatigue and discourage use.<\/p>\n<p>Think about exposure beyond the palm. A longer cuff may protect the wrist and lower forearm when handling sheet materials. For tasks where a blade could contact the back of the hand, a glove with all-round cut resistance may be needed rather than a palm-only design. If chemical exposure is present, confirm the chemical permeation data for the exact substance and concentration. A cut-resistant liner beneath a chemical glove can help in some applications, but only where the combined system has been assessed for fit, dexterity and compatibility.<\/p>\n<h2>A practical specification process for buyers<\/h2>\n<p>A consistent selection process makes glove purchasing easier to manage across departments and sites. Begin with a task-based assessment, then record the minimum protection required, the preferred grip and coating, cuff length, sizing range and any additional standards. This gives suppliers a meaningful brief and prevents selection based on appearance or price alone.<\/p>\n<p>Before placing a larger order, request samples for a controlled wearer trial. Ask users to handle the materials, tools and components they work with over a normal shift. Assess comfort, grip, dexterity, durability and whether the glove interferes with other PPE. Record feedback from supervisors as well as wearers, because early wear, contamination and laundering requirements can affect overall value.<\/p>\n<p>Check that product markings and technical documentation match the stated requirement. Keep certificates and specification sheets with PPE records, and review the selection whenever materials, processes or incident patterns change. A product substitution should be reviewed in the same way, even where the replacement appears similar.<\/p>\n<p>GHS Health &amp; Safety CC can assist organisations in matching recognised glove ranges to task requirements, supporting a more consistent PPE standard across teams.<\/p>\n<p>A clear rating on a glove is a useful starting point, not the finish line. Give workers protection they can wear comfortably, grip confidently and replace before damage compromises performance &#8211; that is where a hand-protection programme earns its value.<\/p>\n","protected":false},"excerpt":{"rendered":"<p>Cut resistant glove ratings explained: learn EN 388 and ANSI cut levels, test methods and how to select gloves that suit the task and workforce safely.<\/p>\n","protected":false},"author":0,"featured_media":5694,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_eb_attr":"","footnotes":""},"categories":[],"tags":[],"class_list":["post-5693","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry"],"_links":{"self":[{"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/posts\/5693","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/types\/post"}],"replies":[{"embeddable":true,"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/comments?post=5693"}],"version-history":[{"count":0,"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/posts\/5693\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/media\/5694"}],"wp:attachment":[{"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/media?parent=5693"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/categories?post=5693"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/ghsprosa.co.za\/index.php\/wp-json\/wp\/v2\/tags?post=5693"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}